This shows you the differences between two versions of the page.
— |
hw:f5d6060 [d-m-Y H:i] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Belkin F5D6060 802.11b CF Card ====== | ||
+ | ===== Description ===== | ||
+ | |||
+ | This card uses the [[http://www.intersil.com|Intersil]] ISL37300P chipset. It is a PRISM 2.5 implimentation and does not require an external firmware. It works out of the box with the orinoco_cs kernel module. | ||
+ | |||
+ | PDF for the {{hw:isl37300p-eval.pdf|Intersil ISL37300P WLAN PCCard reference design}}. | ||
+ | |||
+ | Note that [[http://www.intersil.com|Intersil]] [[http://www.intersil.com/pr/shell/0,1091,1063,00.html|sold]] it's Wireless Networking Product Group to GlobespanVirata, which has since been bought by [[http://www.conexant.com|Conexant]]. | ||
+ | |||
+ | The [[http://www.intersil.com/data/fn/fn8031.pdf|original]] PDF data sheet is no longer available from Intersil, though [[http://www.chipdocs.com/datasheets/datasheet-pdf/Intersil-Corp/ISL37300.html|ChipDocs]] will sell you one. | ||
+ | |||
+ | ===== Hardware ===== | ||
+ | |||
+ | ==== Antenna ==== | ||
+ | |||
+ | |||
+ | ===== Software ===== | ||
+ | |||
+ | ==== Windows CE ==== | ||
+ | |||
+ | Reference drivers for the Prism 2.5 chipset can be downloaded from [[http://www.hpcfactor.com/support/cesd/h/0028.asp|HPC Factor]] | ||
+ | |||
+ | ==== Debian ==== | ||
+ | |||
+ | === Insertion Syslog === | ||
+ | kernel: cs: memory probe 0xe0200000-0xe02fffff: excluding 0xe0200000-0xe020ff | ||
+ | cardmgr[3920]: socket 0: ISL37300P | ||
+ | kernel: orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel R | ||
+ | kernel: orinoco_cs 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pave | ||
+ | kernel: eth3: Hardware identity 800c:0000:0001:0000 | ||
+ | kernel: eth3: Station identity 001f:0004:0001:0003 | ||
+ | kernel: eth3: Firmware determined as Intersil 1.3.4 | ||
+ | kernel: eth3: Ad-hoc demo mode supported | ||
+ | kernel: eth3: IEEE standard IBSS ad-hoc mode supported | ||
+ | kernel: eth3: WEP supported, 104-bit key | ||
+ | kernel: eth3: MAC address 00:02:DD:32:29:09 | ||
+ | kernel: eth3: Station name "Prism I" | ||
+ | kernel: eth3: ready | ||
+ | kernel: eth3: index 0x01: Vcc 3.3, irq 3, io 0xa080-0xa0bf | ||
+ | cardmgr[3920]: executing: './network start eth3 2>&1' | ||
+ | cardmgr[3920]: + Fill with your own settings... | ||
+ | cardmgr[3920]: + iwconfig eth3 mode Managed | ||
+ | cardmgr[3920]: + Debian network setup | ||
+ | cardmgr[3920]: + /sbin/ifup eth3 | ||
+ | |||
+ | === Card Manager === | ||
+ | |||
+ | # cardctl ident | ||
+ | Socket 0: | ||
+ | product info: "PCMCIA", "11M WLAN Card v2.5", "ISL37300P", "RevA" | ||
+ | manfid: 0x0274, 0x1612 | ||
+ | function: 6 (network) | ||
+ | | ||
+ | # cardctl info | ||
+ | PRODID_1="PCMCIA" | ||
+ | PRODID_2="11M WLAN Card v2.5" | ||
+ | PRODID_3="ISL37300P" | ||
+ | PRODID_4="RevA" | ||
+ | MANFID=0274,1612 | ||
+ | FUNCID=6 | ||
+ | | ||
+ | # cardctl status | ||
+ | Socket 0: | ||
+ | 3.3V 16-bit PC Card | ||
+ | function 0: [ready] | ||
+ | | ||
+ | # cardctl config | ||
+ | Socket 0: | ||
+ | Vcc 0.2V Vpp1 99.2V Vpp2 109051904.0V | ||
+ | interface type is irq 3 [exclusive] [level] | ||
+ | function 0: | ||
+ | config base 0x0001 | ||
+ | option 0x00 | ||
+ | io 0xa080-0xa0bf [16bit] |